Just how to Replace a Bathtub (Step By Step).
Just how to Replace a Bathtub (Step By Step).
Blog Article
Listed here in the next paragraph you can locate a bunch of good quality information and facts pertaining to How to Install a Bathtub.
Mounting a bathtub isn't exactly rocket science, however it does need solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is conveniently available, the project can move speedily; if you need to open a wall surface to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need an assistant to move out the old tub and also embeded in the new one. Make sure you have qualified yourself for the job and are comfortable trying it. Rather than working with a service provider to take over a halfway-completed job, it is much better to think about utilizing one prior to you begin. Possibilities are you might need a professional plumber to make tube connections.
This write-up will certainly aid you install a new tub in your restroom if you have actually already gotten a brand-new tub and also don't require to alter the arrangement of your previous water pipes.
Your devices as well as material checklist need to comprise the following:
Planning for the Installation
To start with, the supporting framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, then the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain any type of water remaining in the system. The procedure of removing the existing taps can be fairly problematic because of the limited gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. Once the supply pipes have been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Using both wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by checking the level as well as changing the feet on the bath tub until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the proper supply pipeline by making a compression sign up with; then do the same for the other faucet.
Turn on the water system as well as check all joints and new pipework for leakages and also tighten them if needed. Fill up the bathtub and additionally examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bathtub should wait till the tub has been utilized at the very least once as this will settle it into its last placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making sure that the washers remain in area between the faucet and the sink. Secure the tap in position with the producer supplied backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former kind ought to be linked to the faucet finishes initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, creating the water to penetrate the wall in between the bath and the tiling, causing problems with dampness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and also cartridges, as well as can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before sealing, to permit the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted person who reads about Tools You Need to Install a New Bathtub , I figured sharing that piece of content was a great idea. Liked our blog entry? Please share it. Help others check it out. Thanks for going through it.
Set An Appointment Report this page